Currently, there are no specific tutorials available for replacing the screen on the Redmi Watch 5 Active. However, general guidance on repairing similar devices can be helpful. Here's a detailed approach based on similar smartwatch repairs:
Preparing for the Repair
1. Gather Tools and Materials: You will need a flat-blade screwdriver, a spudger or similar tool, gloves, and a suitable adhesive for reassembly. Ensure you have a replacement screen compatible with the Redmi Watch 5 Active.
2. Turn Off the Watch: Before starting, make sure the watch is powered off to prevent any accidental activations during the repair.
Disassembling the Watch
1. Remove Screws: Typically, smartwatches have screws on the back. Use a suitable screwdriver (e.g., Torx or hex) to remove these. Be aware that some watches may have additional clips or latches.
2. Open the Case: Insert a flat tool like a spudger into any available gaps to pry the case open. Be cautious not to damage any internal components.
3. Disconnect Battery and Components: Once inside, disconnect the battery and any other components connected to the motherboard. This may require tweezers or a spudger.
Removing the Old Screen
1. Identify Adhesive Type: The screen is likely attached with a strong adhesive. Unlike some adhesives, this type may not melt with heat, so warming it slightly might help soften it but won't melt it[1].
2. Apply Heat (Optional): If the adhesive is somewhat responsive to heat, apply gentle warmth using a hair dryer or a heated tool (not too hot) for a few minutes. This can make the adhesive slightly softer.
3. Pry Off the Screen: Use a large flat-blade screwdriver or a similar tool to carefully pry the screen off. Start at one edge and work your way around. Be prepared for the screen to crack if it's old or damaged.
Installing the New Screen
1. Clean the Area: Ensure the area where the new screen will be attached is clean and free of debris.
2. Apply Adhesive: Use a suitable adhesive (preferably designed for screens) and apply it around the edges of the new screen. Make sure to leave some overhang for a clean finish.
3. Assemble the Watch: Carefully place the new screen onto the watch, ensuring it's centered and evenly spaced. Press down gently to secure it.
4. Scrape Off Excess Adhesive: Once the adhesive starts to dry, use a plastic spatula to scrape off any excess adhesive for a clean finish.
Reassembling the Watch
1. Reconnect Components: Reattach any components you disconnected, including the battery.
2. Close the Case: Carefully snap the case back together, ensuring all clips or screws are securely in place.
3. Test the Watch: Turn on the watch and test the screen to ensure it's working properly.
Troubleshooting Tips
- If the screen remains unresponsive after replacement, check for any debris or damage.
- Restart the watch or perform a reset if necessary.
- Ensure the screen is properly aligned and securely attached.
While there are no specific tutorials for the Redmi Watch 5 Active, following these steps and being cautious can help you replace the screen successfully. However, if you're not comfortable with DIY repairs, it's recommended to seek professional assistance to avoid damaging your device.
Citations:
[1] https://xdaforums.com/t/mi-watch-s1-active-digitizer-replacement.4675651/
[2] https://www.ifixit.com/Teardown/Xiaomi+Mi+Watch+2021+Teardown/141415
[3] https://www.youtube.com/watch?v=aeuqKL6gtrI
[4] https://www.youtube.com/watch?v=0REZR1Qrds0
[5] https://www.youtube.com/watch?v=8EuRUb3L7X0
[6] https://play.google.com/store/apps/details?id=com.redmiwatch5activeappguide.kantundev
[7] https://www.youtube.com/watch?v=Gdy6JDaRIVM
[8] https://www.youtube.com/watch?v=gKvcJumTIDg
[9] https://www.youtube.com/watch?v=VUKIXuoZIgk
[10] https://www.ifixit.com/Guide/Xiaomi+Mi+Watch+2021+Battery+Replacement/145447
[11] https://www.nextpit.com/miui-tips-and-tricks
[12] https://www.youtube.com/watch?v=--GVqxDcxbE
[13] https://www.youtube.com/watch?v=R22LIm-u0MA